Distance sensor JSN-SR04T If you are in need of measuring distances with your Raspberry, this tutorial is what you where looking for. In this article, we will look at a JSN-SR04T ultrasonic distance sensor. Which is an affordable sensor for your robotics/home automation/whatever project. Its price starts on $7 on Ebay. For this price you will get a waterproof sensor, that can measure distances between 20cm to 600cm and should work in temperatures from -20°C to +70°C. It claims to have an accuracy of ±1cm, but lets be honest, there are so many things that can influence the measuring, that you will get a higher fluctuance in your measurements than that. This is how it looks like… How to measure distance with sound JSN-SR04T and ultrasonic distance sensor in general works on a simple principle. It sends an acoustic wave (ultrasonic, so you won’t hear it) when it is triggered and then listens for when the wave reflects from some obstacle in front of it and comes back. However, the sensor is only able to send the wave and tell that a wave came back, you will have to do the math to count the distance by yourself (read, you will have to program it by yourself). But read further and you will see it is really easy. From the sensor specification we can find out that the sensor is activated by sending a pulse of HIGH, which is at least 10µs (microseconds) long, on the TRIGGER pinout. Which means that if you want to send a wave, you will need to have a GPIO set to OUTPUT mode, connect it to the TRIGGER pinout and have it set to LOW, then set in to HIGHT for at least 10µs and then set it back to LOW. Shortly after this pulse is received by the sensor (TRIGGER goes from HIGHT back to LOW), the ECHO pinout will go HIGH and the sensor will send a wave at the same time. The ECHO pinout will remain in HIGH position until it receives the wave back, at that moment the ECHO will go back to LOW. Therefore you will need one more GPIO set to INPUT mode and connect it to the ECHO pinout. Then in your program, you will have to wait until it goes HIGHT, then start counting, wait until it goes back to LOW as it received the wave back and then stop the counting. The time you measure is the time a sound wave spend going to the obstacle and back to the sensor. Thanks to many clever minds who did research on speed of sound we now know, that it travels around 332 meters per second at 20°C, keep in mind that it slightly changes with different air temperature. To be more precise, use this equation to count the speed for your conditions (it assumes the air humidity is 0% and that temperature is in °C): speedOfSound = (331.3 + 0.606 * temperature) m/s To tell the distance we only need to multiply the speed of sound with the measured time and divide it by two. That is because the sound wave had to go the distance twice - to the obstacle and back to the sensor. And viola! We have measured the distance! Now lets go connect the sensor to the Raspberry and write a program to count the distances for us… Connecting it to Raspberry JSN-SR04T sensor has four pinouts. First pair is VCC and GND for obvious purpose of connecting it to 5V power and grounding it. And the second pair is TRIGGER and ECHO that we already mentioned in previous section. So simply connect the VCC to 5V, GND to GND, ECHO to a GPIO & TRIGGER to different GPIO. Simple. Reading the distance Now lets create a file called distance.py and write the actual code: #!/usr/bin/python # Import required Python libraries import time # library for time reading time import RPi.GPIO as GPIO # library to control Rpi GPIOs def main(): # We will be using the BCM GPIO numbering GPIO.setmode(GPIO.BCM) # Select which GPIOs you will use GPIO_TRIGGER = 23 GPIO_ECHO = 24 # Set TRIGGER to OUTPUT mode GPIO.setup(GPIO_TRIGGER,GPIO.OUT) # Set ECHO to INPUT mode GPIO.setup(GPIO_ECHO,GPIO.IN) # Set TRIGGER to LOW GPIO.output(GPIO_TRIGGER, False) # Let the sensor settle for a while time.sleep(0.5) # Send 10 microsecond pulse to TRIGGER GPIO.output(GPIO_TRIGGER, True) # set TRIGGER to HIGH time.sleep(0.00001) # wait 10 microseconds GPIO.output(GPIO_TRIGGER, False) # set TRIGGER back to LOW # Create variable start and give it current time start = time.time() # Refresh start value until the ECHO goes HIGH = until the wave is send while GPIO.input(GPIO_ECHO)==0: start = time.time() # Assign the actual time to stop variable until the ECHO goes back from HIGH to LOW while GPIO.input(GPIO_ECHO)==1: stop = time.time() # Calculate the time it took the wave to travel there and back measuredTime = stop - start # Calculate the travel distance by multiplying the measured time by speed of sound distanceBothWays = measuredTime * 33112 # cm/s in 20 degrees Celsius # Divide the distance by 2 to get the actual distance from sensor to obstacle distance = distanceBothWays / 2 # Print the distance print( Distance : {0:5.1f}cm .format(distance)) # Reset GPIO settings GPIO.cleanup() # Run the main function when the script is executed if __name__ == __main__ : main() You can get the code also from my GitLab or just clone the repo to your Raspberry. git clone https://gitlab.com/bambusekd-dev-blog/raspberry-measure-distance-jsn-sr04t.git Once you have the code ready, fire up your terminal on Raspberry, navigate to the folder with your script, point the sensor somewhere and run the script. python distance.py If everything worked as it should, you should see message similar to this in your terminal: Distance : 25.1cm Good job, you have successfully measured a distance between an obstacle and your sensor! Some last thoughts You should always bare in mind, that this sensor has limited capabilities. You have to setup it properly, make sure it points to the place whose distance you desire to measure and also that the speed of sound differs in different temperature/humidity. Also Python’s time library is not the best tool for precise time measurement. For greater precision, I would recommend to use a C program rather than Python. But worry not, if you can tolerate some inaccuracy, then there is no problem using Python and the code provided above. Happy hacking!
Raspberry Course Greetings! I am very glad that you ended up on my blog, mostly focused on programming and electronics. Since you clicked on this post I guess you are probably looking for some learing material to teach yourself how to run and control you
Parking sensor In today’s article, we are going to build a parking sensor. Most of you are for sure familiar with that beeping sound in your car that starts every time you start to back your car and tells you, by changing the beeping frequency, how far y
Raspberry pinouts If you are going to connect some electronics to your Raspberry, no matter if to power them, control them or read dat from them, you will need to use Raspberry’s pinouts, which are those small wires going out of the raspberry in the corn
1-Wire In todays article we will look at an interesting 1-Wire technology and at how it works together with Raspberry. After the brief introduction, you can look forward to a practical demostration of how to use 1-Wire temperature sensor DS18B20. 1-Wire
DHT sensors Have you ever wanted to build your own weather station? Then read further, because today we are going to look at how to measure temperature and humidity with our Raspberry! We are going to use DHT11/22 sensor, which you can get on Ebay for 1